This great article in the next paragraphs on the subject of How to Install a Bathtub is indeed remarkable. Give it a go and draw your own findings.
Mounting a bath tub isn't precisely rocket science, however it does call for strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately hard task. If the old bathtub is conveniently accessible, the job can move speedily; if you need to open up a wall surface to get rid of the old tub and place the new bathtub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly need an assistant to vacate the old tub and also embeded in the new one. Make sure you have actually certified yourself for the job and also fit attempting it. Instead of employing a contractor to take over a halfway-completed task, it is much better to take into consideration employing one prior to you begin. Possibilities are you might require an expert plumber to make tube links.
This article will help you set up a new tub in your restroom if you have actually currently bought a new bathtub and also don't need to transform the setup of your previous supply of water pipelines.
Your devices as well as material checklist ought to make up the following:
Preparing for the Installment
Firstly, the supporting frame provided with the bathroom must be fitted (if required) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to avoid pressure on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, then the first thing you should do is detach the water supply. After doing so, turn on the taps to drain any type of water staying in the system. The process of eliminating the existing taps can be fairly bothersome as a result of the limited accessibility that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a towel ready for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have been gotten rid of, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any kind of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the needed setting. The wood boards are useful in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four tiny points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bath tub up until the level checks out level.
To set up faucets, fit all-time low of the furthest adaptable tap connector to the suitable supply pipeline by making a compression sign up with; after that do the same for the various other tap.
Turn on the water supply and inspect all joints as well as new pipework for leakages and tighten them if necessary. Fill up the bath tub as well as additionally inspect the overflow electrical outlet and also the typical electrical outlet for leaks.
Lastly, take care of the bath paneling as described in the maker's instruction manual. Tiling as well as sealing around the bath tub must wait until the tub has been used at least once as this will certainly resolve it right into its last position.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin making sure that the washing machines remain in place in between the tap and also the sink. Safeguard the tap in place with the producer offered backnut. As soon as the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet adapters. The previous type must be linked to the faucet finishes first, tightening up just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, creating the water to permeate the wall surface between the bathroom and the tiling, resulting in problems with moisture as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to securing, to allow for the movement experienced when the tub is in usage. The sealer can crack rather very early if you do not take into consideration this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that entry about How to Install a Bathtub Yourself when browsing on the search engines. Liked our write up? Please share it. Let somebody else discover it. Many thanks for going through it.
Rely on our service.